Infrared Heating System
Typical installation of Universal 2000 Infrared Heaters
Infrared Heating System
Typical installation of Universal 2000 Infrared Heaters
HI-Density Cartridge Heater
The header cap of this heater is an integral part of the fitting; leads exit through small holes that are sealed with epoxy for moisture protection
Cast-In Thermal Component
Heated sink casting for the Food Service Industry
Shroud System
Stainless steel shrouds for air cooled cast-in band systems
Silicone Rubber Heater
Round heater with center hole used in air horns for motorized vehicles such as trains, semi-trucks or RV's where the leads need to go through the center
Silicone Rubber Heater
Heater vulcanized to black anodized aluminum for food-prep station (metal component also supplied by Tempco)
Silicone Rubber Heater
An insulating heater used on a compressor pump to prevent freezing in Siberia
Silicone Rubber Heater
Small heater used to remove condensation in a gas filter is designed with two holes, two slits and Velcro® for easy installation while filter is in use
Silicone Rubber Heater
Formed heater with six thermocouples for six-zone control used to refurbish airplane propellers by applying heat to cure an epoxy compound that attaches a new nickel lead edge to the propeller blade
Silicone Rubber Heater
Long heater design (up to 12')
Silicone Rubber Heater
Heater manifold 3D formed for use on a snow making machine
Silicone Rubber Heater
Cone heater with laces used on a soup dispenser kettle
Silicone Rubber Heater
Heater vulcanized to a metal plate is mounted in a refrigeration unit to minimize condensation within the control panel (metal component also supplied by Tempco)
Silicone Rubber Heater
Adhesive backed heater formed for irregular shaped pipes/tubes with thermostat.
Silicone Rubber Heater
Adhesive backed heater formed for irregular shaped pipes/tubes with thermostat.
Silicone Rubber 55 Gallon Drum Heaters
Silicone Rubber Drum Heaters come in a variety of sizes. Tempco also manufactures 5, 15 and 30 gallon drum heaters.
Silicone Rubber Heater
Heater vulcanized to the shaft in the base of a weather vane is used for freeze protection (machined parts also available from Tempco)
Silicone Rubber Heater
Formed heater used to remove condensation on a vacuum canister
Cast-In Thermal Component
Heater for Semiconductor Manufacturing
Infrared Array
Ceramic E-mitter heating array
Infrared Array
Heater array with Ceramic E-mitters, handles and mounting brackets
Infrared Heating System
Custom ARV Array housing assembly designed with KTG E-mitters
Ceramic Fiber Heater
Special half round heater
Temperature Sensor
137.5" long Thermocouple 5 x Multipoint for simulating a nuclear reactor
Temperature Sensor
Thermocouple
Temperature Sensor
Thermistor
Temperature Sensor
Thermistor
Temperature Sensor
Thermocouple
Temperature Sensor
Thermistor
Temperature Sensor
RTD
Temperature Sensor
Temperature Sensor
RTD
Temperature Sensor
Thermocouple
Temperature Sensor
RTD
Temperature Sensor
Thermocouple
Temperature Sensor
Thermocouple
Temperature Sensor
RTD
Temperature Sensor
Magnet thermocouple
Temperature Sensor
Pipe clamp thermocouple
Temperature Sensor
Thermocouple
Temperature Sensor
Thermocouple
Finned Tubular Element
Finned Tubular Heating Elements can be manufactured in-house to virtually any shape or size, even elements 17ft long.
Immersion Cartridge Heater
Heater with built-in thermostat, pipe fitting and ground leads for oil heating in waste handling equipment
Low Density Cartridge Heater
Heater with built-in thermal fuse and ground wire for X-Ray processing equipment
Cable Heater
Cable Heater
Double Coiled
Coil Heater
Cable Heater
Coil design with multiple heat zones
Coil Heater
Custom coil design with custom mounting flange
Coil Heater
Heater coil inside specially designed protective clamp with bayonet adaptor for thermocouple
Cable Heater
Heater coil with flange
Cable Heater
Coil heating element embedded into metal plate
Cable Heater
Donut shaped coil design
Cable Heater
Custom coil formation
Cable Heater
Custom coil design
Coil Heater
Cable heater inside specially designed protective clamp
Coil Heater
Dual element heater
Cable Heater
Custom formed element with custom termination
Process Control Panel
Custom two-zone control panel designed with TEC-9100 controller, type J thermocouple, electronic timer and wall or bench mounting options
Process Control Panel
NEMA 4 control panel with alarm light and window protection kit for controlling paraffin wax tank heaters.
Process Control Panel
High limit Panel with 8 zones and top beacon warning light
Process Control Panel
304 Stainless Steel, NEMA 4x control panel featuring a thermostat-controlled, side-mounted air conditioner that maintains safe interior temperatures for the electronic components while operating in high outdoor ambient temperatures
Process Control Panel
Control Panel for a 90KW skid mounted fuel circulation system for heating in waste reduction management
Process Control Panel
Portable heat treat system with Ramp/Soak TEC Temperature Controllers and additional electronics mounted in a custom sized portable stainless steel cabinet to power silicone rubber heating elements
Process Control Panel
Outdoor control panel with NEMA 4 construction and enclosure heater for a 1,000 gallon water holding tank with internal temperature control
Process Control Panel
Outdoor control panel with NEMA 4 construction and enclosure heater for a 1,000 gallon water holding tank with internal temperature control
Process Control Panel
Used in paint curing for decorative landscaping rocks and stone
Immersion Heater
A basin sump-pump heater with float switch, for use on construction excavation sites
Process Heating System
Chemical Bath Heater
Metal tube over-the-side chemical bath heater
Tubular Heater Array
Custom heater array for an application requiring infrared heat
Tubular Heater
Tubular Heater
Heater formed in circular pattern
Circulation Heater
Custom flange heater for Sanitary Process Solutions
Circulation Heater System
90KW skid mounted fuel circulation system for heating in waste reduction management
Duct Heater
Heater with NEMA housing; NEMA 4 (moisture resistant), NEMA 7 (explosion resistant) and NEMA 12 (dust resistant) are all available
Duct Heater
Application specific with foldback bends
Duct Heater System
Heater and blower assembly ready for connection to duct work for drying metal parts after being coated with a rust inhibitor; 48KW, 480 V unit produces 15 CFM heated air
Duct Heater
Heater with completely sealed, insulated housing for a medical product manufacturing application; prevents contamination from entering the air stream
Duct Heater
Heater for high temperature application where the electrical housing is separated from the heater flange to lower the ambient temperature of the electrical wiring
Mica Strip Heater
Ring heater with mounting holes
Mica Strip Heater
Ring heater with mounting holes
Mica Strip Heater
Two Piece Ring heater with mounting holes
Cast-In Thermal Component
Complex thermo-platen for the food service industry
Mi-Plus (Mineral Insulated) Band Heater
Four-piece heater with spring-loaded clamping and independent electrical circuits on each segment
Mi-Plus (Mineral Insulated) Band Heater
Heater with separate strap designed for three-phase operation, with ground terminal and thermocouple clearance hole
Mi-Plus (Mineral Insulated) Band Heater
Two-piece heater with spring-loaded clamping and single leads for easy wiring
Mi-Plus (Mineral Insulated) Band Heater
Two independent electrical circuits in a single heater with dual wattage and dual voltage option and thermocouple clearance hole
Mi-Plus (Mineral Insulated) Band Heater
Partial coverage with spring-loaded clamping and wire braid leads
Maxiband Heater
Type RC: Reverse Construction Maxiband heater to heat a cylindrical surface from the inside out
Maxiband Heater
Maxiband heater for rectangular extruder application
Ceramic Band Heater
Made with staggered/offset insulators for easier installation
Ceramic Band Heater
Type R: Uninsulated heater with perforated SS outer shell for more efficient cooling
Cast-In Thermal Component
Barrel adapter for polymer extruder equipment
Cast-In Thermal Component
Thermo-platen with top-surface grid
Cast-In Thermal Component
Autoclave aluminum cast-in heater, electroless nickel-plated for sterilizing dental instruments
Cast-In Thermal Component
Hopper feed cooler
Infrared Heater System
Dual element heater system with controller containing 8 CRH E-Mitters and 8 CRZ E-mitters
Tubular Heater
Custom heater formed to plate for mouting
Tubular Heater
Custom tubular formation
Tubular Heater
Small custom design
Tubular Heater
Heater for Hot Runner Manifold application
Pennybottom™ Cartridge Heater
Pennybottom tip die bolt heater with internal thermocouple
Shroud System
Cool to-the Touch Dual Layer Shrouds use finned cast-in bands and attached blowers to create an air cooled system
Hi-Density Cartridge Heater
Internal thermocouple is wired to a serial connector for easy assembly to a microprocessor used in incubators
Cast-In Thermal Component
Used in a thermoforming mold
Tubular Heater
Heater formed in circular pattern
Cast-In Thermal Component
Cast iron manifold heater for aluminum low pressure casting machine
Cast-In Thermal Component
Cast-In platen used for heating a custom rectangular extruder barrel
Immersion Cartridge Heater
Finned cartridge oil immersion heater with liquid-tight electrical termination
Hi-Density Cartridge Heater
SJO cord and molded plug termination for automotive air conditioning charging units
Hi-Density Cartridge Heater
SJO cord and molded plug termination for automotive air conditioning recharging units
Immersion Cartridge Heater
Incoloy® fitting and seamless Incoloy® 800 sheath material used in an aviation application
Hi-Density Cartridge Heater
Designed with straight armor cable and adjustable bayonet cap for easy assembly
Low Density Cartridge Heater
Heater with NPT fitting and 5-pin industrial connector molded to the cord
Hi-Density Cartridge Heater
Heater designed to run continuously at 1202°F (650°C); designed with built-in isolated thermocouple and ground wire
Hi-Density Cartridge Heater
Complex shape cartridge heater
Hi-Density Cartridge Heater
Complex shape cartridge heater
Air Immersion Cartridge Heater
Heater with custom designed fins for air heating in natural convection environment in a plastic-processing machine
Air Immersion Cartridge Heater
Heater for medical diagnostic instruments has an integrated heat sink and thermal fuse
Air Immersion Cartridge Heater
Cartridge heater for continuous air heating application with Incoloy® sheath, custom machined fitting and silicone rubber moisture barrier
Duraband (Mica Insulated) Heater
Mica insulated band heater designed for a square or rectangular barrel
Mi-Plus (Mineral Insulated) Band Heater
Nozzle heater for magnesium machine
Duraband (Mica Insulated) Heater
Three mica strip heaters connected together to form a triangular heater
Duraband (Mica Insulated) Heater
Arch shaped heater for a special die - a two-piece heater will cover an obround die
Duraband (Mica Insulated) Heater
Heater with miniature outlet box and clearance hole
Duraband (Mica Insulated) Heater
Fully flexible tapered two-piece heater
Duraband (Mica Insulated) Heater
Two-piece rectangular heater with corner radius and cutouts
Duraband (Mica Insulated) Heater
Dual circuit unit has two heaters in one envelope
Duraband (Mica Insulated) Heater
Boat-shaped two-piece heater
Duraband (Mica Insulated) Heater
Heater with large cutout at gap and clearance holes
Duraband (Mica Insulated) Heater
Fully flexible one-piece heater with varying width
Duraband (Mica Insulated) Heater
Long conical two-piece heater
Mi-Plus (Mineral Insulated) Band Heater
Heater with insulating shroud to minimize energy losses
Cast-In Thermal Component
Bronze electroless nickel-plated cast-in heater used in equipment that tests nuclear hazardous waste
Cast-In Thermal Component
Internal ring heater
Cast-In Thermal Component
Cast aluminum motor housing and base with integral liquid cool capabilities used for medium to large horsepower electric motors - can be made for any size motor. [Developed and patented by Tempco: U.S. Patents: #6222289 & #5939808]
Cast-In Thermal Component
System for pre-heating and mixing chemicals for sand cores
Cast-In Thermal Component
Bronze cast-in heater used in helicone mixture to heat high viscosity material
Cast-In Thermal Component
Heater used on a custom rectangular barrel for a monofilament line extruder
Cast-In Thermal Component
Valve and flange heater used to improve viscous material flow
Cast-In Thermal Component
Irregular Shaped Finned Cast-In Band Heater
Cast-In Thermal Component
Aluminum L-shaped heater with cooling tubes and brass fittings
Cast-In Thermal Component
Cooling jacket for a reclaim pipe line “T” junction
Cast-In Thermal Component
Cast-In heater for melt pump
Cast-In Thermal Component
Bronze cast-in heater used to maintain hydraulic oil temperature
Cast-In Thermal Component
Aluminum cast-in heater for plastic extrusion
Cast-In Thermal Component
Heating and cooling cylinder used in lab testing equipment
Shroud System
Cast-In Thermal Component
Manifold valve assembly thermal component
Cast-In Thermal Component
Liquid cool thermo-platen used for cooling high density electronic systems
Cast-In Thermal Component
Heating elements and aluminum cast over steel transfer feed pipe
Shroud System
Cast-In Thermal Component
Bronze cast-in heater for package sealing machine
Shroud System
Shroud System
Cast-In Thermal Component
Liquid cool cast-in thermal component
Cast-In Thermal Component
Heater designed for the Food Service Industry
Cast-In Thermal Component
Used in the Packaging Industry for adhering tax stamps to cigarette packs
Cast-In Thermal Component
Complex transfer/feed pipe heater
Cast-In Thermal Component
Complex transfer/feed pipe heater
Cast-In Thermal Component
Heater for wafer processing
Cast-In Thermal Component
Used as part of a feed nozzle in a candy processing machine
Cast-In Thermal Component
Brass casting used in industrial processing machinery
Cast-In Thermal Component
Aluminum cast-in heater used in the Carpet Mill Industry
Shroud System
Custom shroud system with Ceramic Band Heaters for the Plastics Processing Industry
Cast-In Thermal Component
Two-piece cast-in transfer/feed pipe heater
Cast-In Thermal Component
Large custom thermo-platen
Cast-In Thermal Component
Heater for the Semiconductor Processing Industry
Cast-In Thermal Component
Bronze cast-in heater for a laminating press
Cast-In Thermal Component
Used for heating beakers in a laboratory environment
Cast-In Thermal Component
Used to decrease viscosity in glue processing
Cast-In Thermal Component
Waste treatment sanitation equipment heater
Cast-In Thermal Component
In-Line system for pre-heating water to induce humidity in baking ovens
Cast-In Thermal Component
"U" shaped heater
Tubular Heater
During application these tubular heaters are placed facing each other forming a tunnel around a pipe to gradually apply less and less heat to prevent sudden exposure to ambient air.
Shroud Systems
Tempco can manufacture a wide variety of sizes for Cool to the Touch systems and Finned Aluminum Cast-in Heaters
Process Heaters
Large Diameter Flanged Air Heater
Process Heaters
Flanged Immersion Heaters used to heat tanks as part of the micro brewing process.
Silicone Rubber Heater
Dome Heater with Boot Hook Mounting
Tubular Heater
Custom heater design with two mounting flanges
Tubular Heater
Tubular heater with custom mounting flange
Tubular Heater
Tightly wound tubular heater with flange
Mica Strip Heater
Irregular shaped, non-metal sheath strip heater
Ceramic Fiber Heater
Half round Ceramic Fiber Heater
Cast-In Circulation Thermal Component
Large-sized cast circulation heater used in hot water, high pressure washer system
Cast-In Circulation Thermal Component
Mid-sized cast circulation heater used for testing aerospace subcomponents
Cast-In Circulation Thermal Component
Compact cast circulation heater used in fuel cell testing equipment
